Craftsman 247.886640 Manuel d'utilisateur

Owner’s ManualCRAFTSMAN'5.0 Horse Power24” Two-Stage Wheel DriveSnow ThrowerModel No.247.886640CAUTION: Before using this product, read this manu

OPERATIONKnowing your Snow ThrowerAWARNING: Be familiar with all the controls and their proper operation. Know how to stop the machine and disengage t

Before StartingAWARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.• The engi

• When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually t

To Engage Augers• To engage the augers and start throwing snow, squeeze the auger control grip against the left handle. Release to stop the augers.Op

LubricationAWARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multiviscosity oils will result in increased oil consu

Remove the frame cover underneath the snow thrower by removing six self-tapping screws. For tocation of the frame cover, see Figure 19.When the tracti

To remove shave plate, remove the carriage bolts, cupped washers and hex nuts which attach it to the snow thrower housing. See Figure 22, Reassemble n

Drive Belt• Follow lirst four steps of previous instructions.• Pull idler pulley up, and lift belt off engine pulley and friction wheel disc. See Fi

OFF-SEASON STORAGEIf the snow thrower will not be used for 30 days or longer, or at the end of the snow season when the last possibility of snow is go

TABLE OF CONTENTSContentPageContentPage...2Service & Adjustment...15...3Off-Season Storage...

TROUBLE SHOOTING GUIDETroublePossible Cause(s) Corrective ActionEngine fails to start Fuel tank empty, or stale fuel.Blocked fuel line.Choke not in ON

PARTS LISTSEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640Safety & Decorative Labels Map777D04651777I20329777120327777S30514fAiMMaaE77712033

9SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640Key No. Part No. Description1618-0123 Housing—R.H.618-0124Housing—L.H,2 710-0642 Hex Screw 1/4-

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640IMPORTANT; For a proper working machine, use Factory Approved Parts. V-BELTS are specially desig

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640NOTE: For painted parts, please refer to the list of color codes below. Please add the applicabl

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640Key No.Part No.DescriptionQty. Key No.Part No,DescriptionQty.------1-----712-OfreLock Jam Nul 3/

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640NOTE: For painted parts, please refer to the list of color codes below. Please add the applicabl

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640Key No.Part No.Description Qty.Key No.Part No.Description Qty.1705-5234Clutch Lever Assembly - R

SEARS CRAFTSMAN 5.0 H.P. SNOW THROWER MODEL 247.886640.27Drive Clutch CableAuger Clutch CableNOTE: For painted parts, please refer to the list of colo

CRAFTSMAN ENGINE 143.015007 FOR SNOW THROWER MODEL 247.886640 V37KeyNo.Part No.DescriptionQty,0640084ACarburetor (Incl. 184 on page 33) 11 631615Throt

AAIMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions which, if not followed, could endanger the personal safety an

CRAFTSMAN ENGINE 143.015007 FOR SNOW THROWER MODEL 247.886640Q130B'' 1276^292/S-|1w285 93^/ /W 0287 390sfOK» «Tjl3700-^9.^15 328 '&apos

CRAFTSMAN ENGINE 143.015007 FOR SNOW THROWER MODEL 247.886640Key No.Part No.DescriptionQty.Key No. Part No.Description Qty.0 RPM High 3450 to 3750 0 1

CRAFTSMAN ENGINE 143.015007 FOR SNOW THROWER MODEL 247.886640Table continued trom previous page:Key No.Part No. DescriptionQty.305 35554 Oil Fill Tube

Recoil StarterCRAFTSMAN ENGINE 143.015007 FOR SNOW THROWER MODEL 247.886640Key No.Part No.DescriptionQty.0 590742Rewind Starter13 590740Retainer16 590

6. Do not operate machine while under the influence of alcohol or drugs.7. Muffler and engine become hot and can cause a burn. Do not touch.8. Exer

HARDWARE PACKLay out the hardware according to the illustration below for identification purposes. Part numbers are shown in parentheses. (Hardware pa

ASSEMBLYNOTE: References to right or ¡eft side of the snow thrower are determined from behind the unit in the operating position.Unpa

(Use hardware group A.)* Insert one each of hex bolt (B) and lock washer (C), from Group A of the hardware pack, through the bottom hole in left hand

AWARNING: Do not over-tighten the clutch cables. Tension on either cable in the disengaged (up) position may override the safety feature

Adjust the chute directional control bracket so that the spiral on the chute directional control fully engages the teeth on the chute assembly. See Fi