Craftsman 113.198611 Operators Manuel de l'opérateur Page 85
- Page / 120
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Fig. 179
Arm and Column
With the miter lock unlocked and in the unin-
dexed position the arm should fit snugly to
the column tube and not allow any vertical
movement. If you can move the end of the
arm up and down an adjustment is needed.
1. With a #2 Phillips screwdriver remove two
screws and the rear arm cover.
2. With a 9/16 inch wrench or socket tighten
evenly the top two 3/8-16 hex head tapping
screws. The bottom two screws should also be
tightened evenly but not as tight as the top
screws. (Figure 180)
4. Holding the wrench and arm in position
rotate yoke to a non-preset position and
rotate swivel lock to the locked position. If the
yoke can still be moved the square nut has not
been tightened enough. Repeat step 3.
5. When the adjustment is such that the yoke
can no longer be moved when the swivel lock
is in the locked position. Install the two
screws.
6. Unlock swivel arm and rotate yoke to a
non-preset position. Return yoke to a rip
position. If the index pin does not securely
seat at the preset position, the adjustment is
too tight. Remove the two screws and loosen
the square nut one quarter turn until swivel
index pin seats securely.
7. Adjustment is complete when both locking
and preset position functions are working
properly.
8. Re-install the two screws mounting the
wrench portion of the swivel lock.
9. Re-install knob to swivel handle and install
screw and nut in knob.
>
>
>
Fig. 180 - Location of Hex Head Tapping Screws
3. This adjustment is correct when the arm
moves firmly without vertical movement.
4. Re-install the rear arm cover.
Carriage Bearings
The carriage should roll freely but with some
resistance for the entire length of travel. To
check for bearing looseness, perform the fol-
lowing steps.
1. Place yoke in either the in-rip or out-rip
position.
85
- CRRFTSMRN 1
- Table of Contents 2
- Safety Information 3
- Personal Safety 5
- Work Area Safety 5
- I DANGER I 6
- Putting Your Saw Together 7
- Information 10
- Model 113.198611 11
- _r Bracket 12
- Smooth Pin In Groove 14
- H S°r'a e 15
- Model 113.198411 19
- Long End Of Shelf 20
- Right Side Panel 21
- , Upper Support 23
- Mounting the Motor 25
- Mounting the Saw 26
- Mounting Table Locks 27
- Mounting the Front Table 28
- I Holes o \ 29
- Putting Drawers in Place 30
- Removing Drawers 30
- On/Off Switch 31
- Bevel Lock 32
- Swivel Lock 33
- Rip Lock 33
- All Controls 34
- Alignment of the Blade 35
- Leveling Front Table 36
- Fig. 101 37
- Fig. 100 37
- Adjusting Table Locks 38
- Squaring Crosscut Travel 39
- Squaring Blade to Table for 41
- Crosscutting 41
- Squaring Blade to Fence 42
- Square Squa 43
- 6. Unlock the swivel lock 43
- Fig. 113 43
- Fig. 118 45
- Making Blade Parallel to 46
- Installing Guard / Setting 47
- Spreader 47
- _A/RS / CRI1FT$1dRN 50
- ELECTRONIC MEASUREMENT 50
- Installing the Battery 51
- [ °._qc, 52
- I q,-,,-,I 53
- Setting Zero References 54
- 1 '-"-'I 55
- Electrical Connections 56
- Extension Cords 57
- Safety Information for 59
- Blade Guard, Anti-Kickback 60
- Pawls and Spreader 60
- Crosscut Checklist 61
- Wear safety 62
- Making Crosscuts 63
- Repetitive Crosscuts 64
- Saw Positions for Ripping 65
- Rip Cutting Checklist 68
- Making a Rip Cut Table Kerf 69
- Adjustments for Ripping 69
- Making Rip Cuts 70
- 13. Turn the saw off 72
- Fig. 160 Edging Label 73
- Accessory Safety 73
- Cutting Accessories 74
- Auxiliary Fence and Push 75
- .o.e:A,,O. oosions,:,nohe 76
- Featherboard 77
- *Recommended Accessories 78
- Glossary 79
- Helpful Hints 80
- Decimal Equivalent 81
- Maintaining Your Saw 82
- Column Tube 83
- Fig. 176 - Collapsed Bellows 83
- Adjustments for Wear 84
- Manual Reset Button 88
- Changing Motor Voltage 89
- Troubleshooting 90
- Electronics - 2 91
- Motor - 2 92
- Saw Operations 93
- Saw Operations - 2 94
- Saw Operations - 3 95
- Figure 1 96
- FIGURE 1 97
- Figure 2 98
- Figure 3 100
- FIGURE 5 - ARM ASSEMBLY 105
- FIGURE 6 - TABLE ASSEMBLY 106
- Description 107
- Figure 8 108
- Figure 9 110
- FIGURE 11 - MOTOR ASSEMBLY 113
- FIGURE 12 - GUARD ASSEMBLY 114
- SEA/R 120
Produits connexes et manuels pour Scies circulaires Craftsman 113.198611 Operators
(20 pages)
(62 pages)Whirlpool AQLF9F 49 U (UK) manuels
Manuels d'utilisation et guides de l'utilisateur pour Machines à laver Whirlpool AQLF9F 49 U (UK).
Nous fournissons des manuels en pdf 2 Whirlpool AQLF9F 49 U (UK) à télécharger gratuitement par type de document : Mode d'emploi
Commentaires sur ces manuels