Operator's Manual42" SNOW BLADEModel No. 486.244414PRINTED IN U.S.A.®FORM NO. 41793 (12/15/14)CAUTION:Before using this product, read and fo
10(Right Hand Side View)FIGURE 15STEP 1: (SEE FIGURE 15)• Assemble the two angle lock bars together as shown in gure 6, so that all holes are align
11STEP 5: (SEE FIGURE 19)• Assemble one 5/16" jam nut (J) approximately 3/4" onto threaded end of control cable that has no rubber cap or
12FIGURE 22 (Right Hand Side View)STEP 8: (SEE FIGURE 22)• Assemble the large 1/2" washer (Q) onto the channel pivot pin.• Attach the cha
13FIGURE 26(Left Hand Side View)STEP 12: (SEE FIGURE 26)• Place the end of the blade pivot rod down through the blade pivot shaft. Attach the other
14FIGURE 28 FIGURE 29To Raise or Lower the Snow Blade• Use the handle grip located on the end of the handle tube. To raise the blade, pull back while
15Wheel weights and tire chains must be used with your snow blade for traction. These accessories are available at your nearest Sears retail store.Usi
16To Adjust Blade Spring• The tension of the blade adjust spring may be altered to permit the blade to tilt forward to bypass solid obstructions. To
17TROUBLESHOOTINGCAUSELift mechanism is bindingHandle tube is binding on lift rod.Lock mechanism is out of adjustmentand is not disengaging.PROBLEMBla
18PARTSREPAIR PARTS FOR MODEL 486.244414 - 42" SNOW BLADEBBAA3881030353550333445382346324256 15141939402427 2048483747414125362561696870636265
19REPAIR PARTS LIST FOR MODEL 486.244414 - 42" SNOW BLADEREF. PART NO. QTY. DESCRIPTION1 23114 1 Blade 42"2 23117 1 Wear Plate 42"3 629
2TABLE OF CONTENTS MODEL NUMBER: 486.244414 SERIAL NUMBER: __________________ DATE OF PURCHASE: __________________The model number and seri
® Registered Trademark / TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries ® Marca Registrada / TM Marca d
3FULL SIZE HARDWARE CHARTREF. PART NO. QTY. DESCRIPTIONA 46071 1 Hex Bolt, 1/4-20 x 3-1/4"B 43648 1 Hex Bolt, 1/4-20 x 1-1/2"C 43085 1 Hex B
41 23456710 891112PARTS IN PACKAGES NOT SHOWN FULL SIZECARTON CONTENTS (Loose Parts in Carton)REF QTY PART NO DESCRIPTION13 1 27611 Hanger Bracket, L.
5ASSEMBLY(1) Pliers(1) Hammer(1) Adjustable Wrench (or socket set)(1) 9/16" Open End or Box End Wrench(1) 7/16" Open End or Box End Wren
6IDENTIFY YOUR SUSPENSION BRACKETS• Compare your tractor to the ones shown in gure 4. • If your tractor resembles the top illustration, go to page
7FIGURE 63/8" x 1" HEX BOLT (D) 3/8" LOCK WASHER (R) 3/8" FLAT WASHER (O)1/2" LARGEWASHER (N)R.H. HANGERBRACKETSTEP 2: (SE
8FIGURE 10STEP 2: (SEE FIGURE 10)• Assemble the pivot support bracket to the angle support brackets using four 3/8" x 1" hex bolts (D) and
9SHOULDER BOLTATTACHMENT PINFIGURE 14STEP 4: (SEE FIGURE 14)• Pull out on the attachment pins on the hitch assembly and swing the top of the pins do
Commentaires sur ces manuels