Operator's ManualI CRAFTSMRN°I2.0 Amp Variable SpeedMulti-ToolModel No. 320. 23465_l_ WARNING: To reduce the riskof injury, the user must read an
3.• Vacuum Adapter• ManualInspect the items carefully to make sure that no breakage or damage hasoccurred during shipping. If any of the items mention
ID]_.'_o_[[e_]KNOW YOUR MULTI-TOOL (Fig. 2)Fig. 2LED worklightOn/Off switchLive tool indicator" LED lightcordVentsVacuum adapterDrive shaft;
ON/OFF SWITCH (Fig. 3)1.2.Connect the power cord ofyour Multi-Tool to a standardhousehold power outlet.To turn the tool ON, pushthe on/off switch forw
LIVE TOOL INDICATOR LED LIGHT (Fig. 6)Your Multi-Tool has a "livetool indicator" green LEDlight, located on the back ofthe tool. This light
SELECTING THE APPLICATION ACCESSORY_h, WARNING: If any part is broken or missing, do not attempt to plug in thepower cord or operate the tool until th
NOTE: Replacement Craftsman accessories and additional Craftsman accessoriesare available at Sears and Craftsman retailers. Refer to the model numbers
SANDING (Fig. 9)_, WARNING: Do not touchthe gear box after prolongeduse; it could be very hot.• The removal rate and thesanding pattern are determined
TO INSTALL THE CIRCULAR SAW BLADE_, CAUTION: Wear protective gloves._, WARNING: Use sharp, undamaged saw blades only. Deformed, blunt sawblades or saw
NOTE: The ribs on theshaft and the grooves in theaccessory tools permit a firmconnection of the accessorytools in increments of 30 °around the shaft (
CARBIDE CIRCULAR BLADE(67650)DESCRIPTION (Fig. 16)The Carbide Circular Blade isdesigned to cut out the groutaround wall tiles. It can alsobe used to c
i _ =[e_[_e_'_Warranty Page 2Safety Symbols Page 3-4Safety Instructions Page 5-9Unpacking Page 9-10Description Page 10-11Operation Page 12-13Acce
4. Fig. 19Align the grooves on thecarbide circular blade withthe four raised ribs on thedrive shaft; put the carbidecircular blade onto the driveshaft
CUTTING WITH THE CARBIDE CIRCULAR BLADE (Fig. 21)1.2.3.4.Connect the Multi-Tool to apower source.Draw the cutting lines onthe workpiece.Place the carb
_, WARNING: Check thatthe accessory tool is correctlyattached. Incorrect orinsecurely fastened accessorytool can come loose duringoperation and cause
USING THE SCRAPER BLADE (Fig. 27)1.2.3.Connect the Multi-Tool to apower source.To scrape, put the tool onthe workpiece at a flat angle(not more than 2
4. Fig. 305.Align the grooves on thecarbide triangular rasp withthe four raised ribs on thedrive shaft; put the disconto the drive shaft.(Fig. 30)With
FLUSH CUT BLADE (67653)DESCRIPTION (Fig. 33)• Bi-metal, straight-edge,flush-cut blade.• Designed for cutting wood,plastic, drywall, soft metaland othe
4.5.Align the grooves on theflush-cut blade with thefour raised ribs on the driveshaft; put the blade onto thedrive shaft. (Fig. 36)With your gloved h
Craftsman Carbide circular blade (67650)Craftsman Circular saw blade (67651)Craftsman Scraper blade (67652)Craftsman Flush cut blade (67653)Craftsman
LUBRICATIONAll of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the tool under normal oper
o_.-0 __..4--,c-"0 "0_1 c'-" 0_ _.I..or-_ =°2o.__ _.I..o
The purpose of safety symbols is to attract your attention to possible dangers.The safety symbols and the explanations with them deserve your carefula
2.0A Variable Speed Multi-Tool MODEL NUMBER 320.23465The Model Number will be found on the Nameplate attached to the handle ofthe Multi-Tool. Always m
24 3700352000 Washer25 5700205000 Ball Bearing26 5660144000 Circlips For Shaft27 3125185000 Dust Cover203 2823034000 Drive Housing ASSY28 5700022000 N
Your HomeFor troubleshooting, product manuals and expert advice:managemylifewww.managemylife.comFor repair - in your home - of all major brand applian
Some of these following symbols may be used on this tool. Please study themand learn their meaning. Proper interpretation of these symbols will allow
_, WARNING: Be sure to read and understand all instructions in this manualbefore using the Multi-Tool. Failure to follow all instructions may result i
When operating a power tool outdoors, use an extension cord suitablefor outdoor use. Use of a cord suitable for outdoor use reduces the risk ofelectri
• Do not use the power tool if the switch does not turn it on and off. Anypower tool that cannot be controlled with the switch is dangerous and mustbe
Use only identical replacement parts when servicing a tool. Followthe instructions in the Maintenance section of this manual. Use ofunauthorized parts
Do not restart a cutting operation in the workpiece. To resume a cuttingoperation: while keeping the tool from contacting the workpiece, allow thetool
Commentaires sur ces manuels