_- Save This Manual _'_For Future ReferenceSWARSowner'smanualModel No.113.235300SerialNumberModel and serial numbersmay be found on a platea
Alignment/Adjustments (continued)Step Three-Checking and Adjusting BladeSquareness to Fence (Front Fence Position)1 To check blade squareness to fence
Step Four-Pivot AdjustmentsNOTE: These adjustments were made at the factory andnormally do not require readjustment.1 .The miter saw should rise compl
Alignment/Adjustments (continued)Fence PositionsThe miter saw has two fence positions The front fenceposition is used for workpieces up to standard 2
8.Install tile outer blade collar, arbor washer and arborscrew Press the arbor lock and turn the 1/2" wrenchcounter clockwise to secure the blade
Mounting The Saw (continued)If the saw is to be used in a portable applica-tion, mount the saw to a 3/4" piece of plywood.The mounting board can
Catalog No. 9-22244 Leg SetO O O O©cD oo CDcD CD 0'lido c)o cDOO 0 O OI- 14 -IFront SideAttach mounting board to holes indicatedSafety Instructio
Safety Instructions for Basic Saw Operations (continued)To Avoid Injury From Jams, Slips Or ThrownPieces• Use Only Recommended Accessories. (See page2
• Clea+ ew.wtfung except the wgrkpm(e and flaredsupport deviso<_ .ff the table before tHrnind th_ rnitetsaw )PI• Secure Work. tJse damps or a ,/so
Basic Saw OperationsWARNING: For your convenient use, your saw has Ia blade brake. The brake is not a safety device.Never rely on it to replace proper
Bevel CutWhen a bevel cut is required, tilt the blade to desiredbevel angle. Stand to the left side of the handle to makethe cutCompound CutWhen a com
FULL ONE YEAR WARRANTY ON CRAFTSMAN BENCH TOP TOOLSIf this miter saw fails due to a defect in materia! or workmanship within one year from the date of
Basic Saw Operations (continued)Cutting Bowed MaterialBefore cutting a workpiece, check to make sure it is notbowed. !f it is bowed the workpiece must
AuxiliaryFenceCe(tainlypesof moldingneeda fencefaceextensionduetothesizeandpositionoftheworkpiece.Holesareprovidedinthefenceto attachanauxiliaryfencem
Basic Saw Operations (continued)Helpful Hints When Cutting CompoundMitersTips for Cutting Compound Miters on PictureFrames and BoxesA compound miter i
Cutting Crown MoldingsPlan Ahead so that you are not tempted to reach acrosssaw blade to steady newly severed workpiece.Crown Moldings can be cut usin
Maintenance And LubricationMaintenanceAlways unplug the power cord befor ,= any maintenancecheck on this saw.DANGER: Never put lubricants on the blade
Troubleshooting GuideMotorProblem Probable Cause Suggested Corrective ActionBrake does not stop 1. Brushes not seated or lightlyblade within 6 sec- st
Wiring DiagramWhiteBlackTriggerSwitchGrayBrake(White) Brush(Red) Brush26
Notes27
Repair PartsParts List for Craftsman 10" Compound Miter Sa',-JModel No. 113.235300Figure 121(15 ---_14-----"_ .,_---- 11121328
Repair PartsParts List for Craftsman 10" Compound Miter SawModel No. 113.235300Figure 1Always order by Part Number- Not by Key NumberKey Part No.
Before Each UseInspect your miter saw.Disconnect The Miter Saw To avoid injury from accidental starting, unplug the saw, before changing thesetup, cha
Repair Parts\! 211520 /19Parts List for Craftsman 10" Compound Miter SawModel No. 113.235300Figure 22 3-_\ 1214\I ARNING: For your safety, this m
Repair PartsParts List for Craftsman 10" Compound Miter SawModel No. 113.235300Figure 312/11107/Always order by Part Number- Not by Key NumberPiv
18 19172021/\t623 2425 269111345"0r-"=,,(,t0om-_z_"IooonZ_(/1==15 13 14
Repair PartsParts List for Craftsman 10" Compound Miter SawModel No. 113.235300Figure 4Always order by Part Number - Not by Key NumberBlade and B
Notes34
Notes35
SEARSowner'smanualModel No.113.23530010 Inch CompoundMiter SawThe model number of your 10inch Compound Miter Saw willbe found on a plate attached
Safety Instructions For Miter Saw (continued)• Do not wear loose clothing, gloves, neckties or jewelry(rings, wrist watches) They can get caught and d
Before freeing jammed material:• Turn switch "OFF"• Unplug the miter saw.• Wait for all moving parts to stop.After finishing a cut:• Keep ho
Motor Specifications and Electrical Requirements (continued)General Electrical ConnectionsDANGER: To avoid electrocution:1. Use only identical replace
Table of Contents'v%'arr a n[ySafety "st',_cttuns Fur M_ter 5a_',Safety S!gnal WordsBefore Us ng The SawWhen nsta nng Dr Mov
Getting To Know Your Miter SawElbow Upper BladeGuard Lock OffButton\\7 Miter Saw/ Handle/1 WarningLabelSwitch;) HandleLatchFenceMiter Scale 4 Miter Lo
Alignment/AdjustmentsWARNING: To avoid injury from unexpected start-ing or electrical shock, do not plug the saw in. Thepower cord must remain unplugg
Commentaires sur ces manuels