Craftsman 351.217880 Manuel de l'opérateur

Operator's ManualCRRFWSIqRH°Bench TopJOINTER/PLANERModel No.351.217880CAUTION: Read and followall Safety Rules and OperatingInstructions before F

WARNING: Turn the switch to OFF position andunplug jointer/planer from power source before pro-ceeding to do maintenance workCHECKING FOR WORN BLADESC

• Replace bottom cover. Secure with screws.• Make sure blade guard functions appropriately.REPLACING DRIVE BELTRefer to Figures 23 and 25.• Turn the s

SYMPTOMMotor does not startMotor stalls (resulting in blownfuses or tripped circuitbreakers)Motor starts slowly or fails tocome to full speedMotor run

NOTES13

Model 351.217880Figure 24 - Replacement Parts Illustration for Fence and Infeed Table98\6 12/J19_8 \1472232_33\36354037/4139/!444614

KEYNO. PART NO.1 18963.002 STD8405083 STD8406104 18954.005 18410.006 18454.007 18411.008 STD8520089 01822.0010 18412.0011 18413.0012 18414.0013 00179.

Model 351.217880Figure 25 - Replacement Parts Illustration for Base18/17932 4033 X2831/2 341jJI48474645543716

KEYNO. PART NO.1 N/A2 STD3152153 00519.004 08077.005 00090.006 18440.007 18441.008 01903.009 18958.0010 18957.0011 18964.0012 00968.0013 03855.0014 18

CEPILLO MECANICO/CEPILLADORA DE BANCOde 61/8"Modelo No.351 •217880PRECAUCION: Lea y siga todas las Reglasde Seguridad y las Instrucciones de Oper

• Evite que la herramienta se encienda por accidente.AsegtJrese de que el interruptor est,. en la posicidn OFF(apagado) antes de enchufar.• No fuerce

Warranty... 2SafetyRules... 2-3Unpacking... 3Assembly...

Insertelamaniveladeinclinacidndelaguiaconelanilloseparadorporeleslabdnderechoyenrosqueeneleslabdnizquierdo.Manivela Conjuntodedeinclinaci6n-_ _%%._ J

• Cercidrese de que no se meza el cepillo mec_.nico/cepilladoray que est6n niveladas las planchas.11" 91/4"ILS/l_,,JP-171/4! _F-19"Figu

MOTOREl cepillo mec_.nico/cepilladora incluye un motor de 2 HP(desarrollado al m_.ximo).El motor universal de CA de 120 voltios tiene las siguienteses

PROFUNDIDAD DEL CORTEConsulte la Figura 10.La profundidad del corte se ajusta por la posici6n relativa de laplancha de alimentaci6n respecto al portac

Las cuchillas han sido ajustadas en f4tbrica para garantizar sucorrecto funcionamiento y no debe ser necesario ajustarlas. Noobstante, el envio y mane

Mantenga unidos los dedos.Haga avanzar la tabla a una velocidad uniforme y continua. Sivacila o par& puede hacer que se corte un "escaldn&quo

ADVERTENClA: Lleve el interruptor a la posici6n OFF (apagado)y desconecte del cepillo mec_.nico/cepilladora de la fuente dealimentaci6n antes de reali

• Vuelva a instalar la cubierta inferior. Asegure con tornillos.• Cercidrese de que el protector de la cuchilla funcionedebidamente.COMO REEMPLAZAR LA

SINTOMAElmotor noarrancaEl motor se para (haciendo quelos fusibles se quemen o loscortacircuitos se abran)El motor arranca lentamenteo no Iogra desarr

NOTAS29

• Use recommended accessories (refer to page 17).Use of improper accessories may cause risk ofinjury to persons.• Handle workpiece correctly. Protect

NOTAS30

NOTAS31

Your HomeFor repair-in your home-of all major brand appliances,lawn and garden equipment, or heating and cooling systems,no matter who made it, no mat

Place a combination square against face of fenceand table surface. The fence and table must be at90° to each other. If not, loosen tilting handle, loo

• Power supply to the motor is controlled by a rockerswitch. Removing the key from rocker switch will lockthe unit and prevent unauthorized use.GROUND

ELECTRICAL CONNECTIONSWARNING: Make sure unit is turned off and discon-nected from power source before inspecting any wiring.The unit is wired as illu

Turning the handwheel counterclockwise will lower theinfeed table causing more wood to be removed fromworkpiece. Turning the handwheel clockwise will

The blades have been adjusted at the factory to assureproper operation and should require no adjustment.However, shipping and handling may have caused

Keep fingers close together.Feed the board at a continuous even rate of speed.Any hesitation or stopping could cause a "step" to becut on th