Craftsman 113.226421 Manuel du propriétaire

SAVE THIS MANUALFOR FUTURE =REFERENCEBELT AND DISCSAN DERSerialNumber.Model and serialnumber may be found onthe back side ofthe base.You should record

i intothe ::waySANDINGPLATESANDINGD_SCINSTALLING BACKSTOP1_ Locate backstop, hex bolt 1/4-20xVz inch, anda 1/4 inch flat washer,2: Hold backstop into

• • :{/:_"i:iii::i::(;:}:_;_:/ &: 'ii}&ii}}_4. Slide table assembly onto rod,WARNING: TO AVOID TRAPPING THE WORKOR FINGERS BETWEEN T

SANDING BELT. USE ONLY SEARS RECOM-MENDED SANDING BELTS. SEE SEARSCATALOG.On the smooth side of the sanding belt you willfind a "directional arro

WARNING: TO AVOID INJURY FROM ACCI-DENTAL START, TURN SWITCH "OFF" ANDREMOVE PLUG FROM POWER SOURCE OUT-LET BEFORE MAKING ANY ADJUSTMENTS.sa

_e::On_Off::Swit_h I:.has::a: ocking feat ure.HIS:: :FEATURE:iS_:]NTENDED TO: HELPREVENT UNAUTHORIZED :AND POSSIBLY_EI:BY CHILDREN ANDsander: ON,:inse

basicBEVEL SANDINGThe worktable can be tilted from 0 ° 45 ° forbevel sanding. Loosen the table lock knob andtilt the worktable to desired angle as sho

a: Loosen theiocknut using a:3/4-inch wrench:b. Place a levei on:the abrasive belt table andusing a 314-|nch wrench, screw the stop boltin or out unti

SANDING CURVED EDGESCURVED EDGESSand inside curves on the idler pulley.Sand outside curves on the sanding disc... _ : .i.,_,. L J u _ , ,I I I, : .4

_:_:::iii:!ii!:::i=ii,!,ii:i:::i_i:iiii:::i:i! iiii!:_i¸!!:i:_::i:::i:i::!i:i::i:::!::¸¸:¸::¸:¸¸CENTERWORKPIECELEFT OFCENTER)BE HAZARThe table may be

troubleshootingWARNING: FOR YOUR OWN SAFETY, TURNSWITCH "OFF" AND REMOVE PLUG FROMPOWER SOURCE OUTLET BEFORE TROUBLESHOOTING YOUR SANDER.TRO

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICECENTERiDEPARTMENT TH ROU GHOUT TH E UNITED STATES.THIS WARRANTY APPLIES ON

n!'partslz:i.mlzO3_J(/)01:3Z_ _,.. :::-t_z0il..%ix:_1_ ¸Q.A0,¢',1

i : ::':: ?i::!i:: :"Li,,IZtOmra7_me!.zw-'<d_z_ ,,-I,'5I,L c,,_ca $'I_0 xo_.Bm "60 cu. 1€_ -r-a. -ord0>_<ood_z!

ii ¸ z ,_ _H • _ui • i¸k¸, •-22

23

SERVgCEMODEL NO.113=226421HOW TO ORDERREPAIR PARTSBEL 7"A ND DiSCSANDERNow that you have purchased your Belt & DiscSander should a need ever

ad safetydiSC sanderinstructions for bett andSafety is a combination of operator commonsense and alertness at alt times when the sanderis being used.W

disc12: Think :Safety...:Safety is a combination of operator common:sense and alterness: at all times when thesander is in operation.WEAR YOUR IThe o

mot0r specifications anrequirements ...emectricamThis machine is designed to use, and is equip-ped with, a 3450 RPM motor. It is wired for opera-tion

FoADIt BEtiNMounting Seltand Disc SanderTo Woi'kbench .: ,, ;:. : ; . ... 7Clamping Belt And Disc SanderTo WOrkbench. ...

8ssem yMOUNTING BELT AND DISC SANDER TOWORKBENCHIf belt and disc sander is to be used in a perma-nent location, it should be fastened securely to afir

INSTALLING:!TIMING BELT :::::: : : , :_ '!::::::::: :.::_:IMPORTANT Do:i:not::::::Ov:ertighten::tim ing belttension by:adjusting,timing setscrew

PULLEY COVERINSTALLING PULLEY COVER1. Locate the pulley cover and one screw114-20xl-3f4".,Place pulley cover into position shown andfasten with o