Craftsman 21609 - 18 in. Scroll Saw Manuel de l'opérateur Page 8
- Page / 28
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EXTENSION CORDS
Use only 3=wire extension cords that have 3=prong
grounding plugs and 3-pole receptacles that accept the
tool's plug. When using a power tool at a considerable
distance from the power source, use an extension cord
heavy enough to carry the current that the tool will draw.
An undersized extension cord wil! cause a drop in line
voltage, resulting in a loss of power and causing the motor
to overheat. Use the chart provided below to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwdter's Laboratories
(UL) should be used.
**Ampere rating (on tool data p_ate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 --
**Used on 12 gauge - 20 amp circuit
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension
cord that is designed for outside use. This is indicated by
the letters "WA" on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
_ WARNING: Keep the extension cord clear of the
working area. Position the cord so that it wil! not get
caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so
can result in serious personal injury.
A
WARNING: Check extension cords before each
use. If damaged replace immediately. Never use tool
with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious
injury.
ELECTRICAL CONNECTmON
This tool is powered by a precision built electric motor.
It should be connected to a power supply that is 120
volts, 60 Hz, AC only (normal household current}° Do
not operate this tool on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor wilt
overheat. If the saw does not operate when plugged into
an outlet, double check the power supply.
SPEED AND WRING
The no=load speed of this too! is approximately 1,600
spm. This speed is not constant and decreases under
a load or with lower voltage. For voltage, the wiring in a
shop is as important as the motor's horsepower rating. A
line intended only for lights cannot properly carry a power
tool motor. Wire that is heavy enough for a short distance
win be too light for a greater distance. A line that can
support one power tool may not be able to support two
or three tools.
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock, This tool is equipped with
an electric cord having an equipment=grounding conduc=
tot and a grounding plug, The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances,
Do not modify the plug provided, If it will not fit the outlet,
have the proper outlet installed by a qualified electrician,
Improper connection of the equipment-grounding con-
ductor can result in a risk of electric shock, The conductor
with insulation having an outer surface that is green with or
without yellow stripes is the equipment-grounding
conductor, If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal,
Check with a qualified electrician or service personnel if
the grounding instructions are not completely understood,
or if in doubt as to whether the tool is properly grounded,
Repair or replace a damaged or worn cord immediately,
This toot is intended for use on a circuit that has an outlet
like the one shown in figure 1, It also has a grounding pin
like the one shown,
FOOTSWtTCN
PLUG
®
SOROLLSAW
PLUG
120V GROUNDED OUTLET
Fig. 1
Produits connexes et manuels pour Outils électriques Craftsman 21609 - 18 in. Scroll Saw
(28 pages)
(62 pages)Canon PowerShot N manuali
Manuali dei proprietari e guide per l'utente per no Canon PowerShot N.
We fornisce 4 manuali pdf Canon PowerShot N per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels