Craftsman 113.239400 Manuel du propriétaire

ILUUIII, I lllllm I,IllLILll,III ILSave This Manual ForFuture Reference A/RSownersmanualMODEL NO.113.239392SHAPER WITH STEELLEGS AND I/2H.P. MOTOR113

item Part Name Qty.A Leg ... 4B * Screw, Truss Hd. 1/4-20 x 5/8 ... 28C

.INSTALLING SHAPER FENCE -FOR STRAIGHT EDGE SHAPING ONLYInstall the fence with two 5/16-18 x 2 inch hex headscrews and two plain washers. These screws

GETTING TO KNOW YOUR WOOD SHAPER8FENCELOCK KNOB9FENCE FACETABLE INSERTMITER GAUGE SLOTTABLE10 CUTTER GUARDPINFE NCEADJUSTING KNOB8 FENCELOCK KNOB2ELEV

C,TO lock switch in OFF position.,, hold switch INwith one hand.,. REMOVE key with other hand.ALWAYS LOCK THE SWITCH "OFF" WHENSHAPER IS NOT

ADJUSTMENTSWARNING: For your own safety, turn switch"off" andremoveplugfrompower source outletbeforemaking anyadjustments..ADJUSTABLE SHAPER

BASIC SHAPINGNOTE: This shaper is designed for use with maximum 2-1/2 inch diameter cutters having a 1/2 inch diameter bore.1. For those operators who

AUXILIARY FENCEPWORK SUPPORTWORKPIECE27 IN.STRAIGHT EDGE SHAPINGCAUTION: The Shaper fence must be used in all straightedgeshapingoperations.1. When sh

IRREGULAR OR CURVED SHAPINGA variety of shapes may be produced w_th the shaper bychanging the the height of cutter in relation to theworkpiece, by usi

3. The starting pin must be used as a pivot to support thework until it has been fed into the shaper collar. TheStarting Pin may be located in either

MAINTENANCEWARNING: For your own safety, turn switch "OFF" andremoveplugfrom power source outlet beforemaintainingor lubricatingyour saw.NOT

ii'_ ... I ii I IFIFULL ONE YEAR WARRANTY ON CRAFTSMAN WOOD SHAPERIf within one year from the date of purchase, this Craftsman Wood Shaper Saw

TROUBLE SHOOTINGWARNING: For your own safety, turn switch "off" and remove plugfrom power source outlet before trouble shooting your shaper.

TROUBLE SHOOTING -- MOTORNOTE: Motors used on wood-working tools are particularly susceptib{e 1othe accumulationof sawdust and wood chtps and should b

REPAIR PARTSPARTS LiST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.239392, 113.239400 AND 113.23942040 41 4233/351\326/1322

PARTS LIST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.239392, 113.239400 AND 113.239420Always Order by Part No. - Not by Key NumberFIGURE 1Key PartNo. No.

PARTS LIST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.2393921 113.239400 AND 113.2394202 1 2!46124 5 69\11 1011 10FIGURE 2 - FENCE ASSEMBLY 72008Key PartN

PARTS LIST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.239392, 113.239400 AND 113.239420KeyNo.12345678910114 3r 1FIGURE 3 - LEGSPartNo.82004060314STD541025

PARTS LIST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.239392, 113.239400 AND 113.239420367 8/FIGURE 4 -ON/OFF POWER OUTLET 60382AND MOUNTING BRACKETKey Pa

JPARTS LIST FOR CRAFTSMAN WOOD SHAPERMODEL NO. 113.239392, 113.239400 AND 113.23942034 /FIGURE 6 - MOTOR PARTS LISTANY ATTEMPT TO REPAIR THIS MOTOR MA

... i i... lu i i i i.iSEAIRSownersmanualSERVICEMODEL NO.113.239392SHAPER WITH STEELLEGS AND 1/2 H.P.MOTOR113.239400SHAPER WITH STEELLEGS AND 3/4

Additional Safety Instructions for Wood ShaperSafety Signal WordsiDANGER: means if the safety information is not followedsomeone will be seriously inj

31.Note and follow Safety tnslructions that appear on theShaper Switch asse.mbly.'...DANGER-'OR YOUR OWK SAFETY:READ ,t_tD LIN0 EFI_TM&ap

UNPACKING AND CHECKING CONTENTSCONTENTSWARRANTY ... 2General Safety Instruction for Power Tools ... 2Addition

LIST OF LOOSE PARTSItem Part Name Qty.A Leg ...4B ' Screw, Truss Hd. 1t4-20 x 5t8 ..

INSTALLING ELEVATING RODAND TABLE SUPPORTPosition table upside down on 2 x 4's on edge for supportand clearance for Spindle assembly.1. Install (

4. Place Belt Guard under Motor [between Motor SupportBracket and Motor Mount) and make certain 5/8" shaftis centered in Belt Guard hole. Install

MOUNTING MOTOR SUPPORT ASSEMBLYTO SHAPER1.Place V-belt on motor pulley and attach motor mountplate to shaper base with two bolts 13/8-18 x t-inch}and