Craftsman 113.225705 Manuel du propriétaire

For Future ReferenceMODEL NO.113.225705SerialNumberModel and serial numbersmay be found on the back sideof the base.You should record both modeland se

ASsembly(continued)usingthe dimensions in the figure. Screw them in untilthere is al/i6 gap between the Screws and the wall... If secUring to drywa

WARNING: To avoid injury from accidental start-ing, always turn switch "OFF", unplug the sanderand remove switch key before removing or repl

Getting!to Know Your Spindle Sanderi : ii L LI L _ [4 Sanding3 Rubber Drum2 Spacer Ring Insert1 Work Table5On,6 Wrench Storage7 Accessory Holder1. Wor

On-Off SwitchThe On-Off switch has a locking feature. This Feature IsIntended To Help Prevent Unauthorized And PossibleHazardous Use By Children And O

tylnstructionsfor:Oscillating iLearn fheSpindleandSanderfunction of 'i i iBefore Usinq The Sander use the ON-OFFswitch.(See page 13)Review:and un

Dress for Safety* Wear nonslip footwear.. Tie back long hair.* Roll long s_eeves above the elbow.oNoise levels vary widely. To avoid possible hearingd

Sanding Metals ...When sandlng me_als,_ sparks or hot fragments could 2. Remove all traces of wood dust from inside the unitcause:a fire::!To av0

WARNING: Always wear safety goggles (notglasses) that comply with ANSI Z87.1 when usingyour sander. Failure to do so could result in dust,shavings, lo

BasicSanding Operation (continued) -_D,, tCOt e tion:Capab.ityA star_dard 2_-l/2"dust:exhaust port has been provided topossible. :ff:is:::located

Sears Recommends The Following AccessoriesDescription Catalog No,Legset ... 9-22243Sears may r

FULL ONE YEAR WARRANW ON CRAFTSMAN BENCHTOP TOOLSe Sander:fails dueto a defect in material or workmanship within one yearfi_omthe date of purchase, RE

_i • _ _i WARNING_ For yourow'n safety, turn switch "OFF", and remove plug from power source outlet before trou-bleshooting your spindl

Notes ...21

Parts List For Craftsman Oscillating Spindle SanderModel 113.225705Figure 136\33\2722i_ _ ii__iii _i_iii_i_iiii_i,_,ii_i_i_ili__i •

Repair Parts ...Parts List For Craftsman Oscillating Spindle SanderModel 113.225705AJways order by Part Number--Not by Key NumberFigure

MODEL NO.113.225705The model number of yourSpindte Sander may be foundon the back side of the baseWhen requesting service orordering parts, always pro

Before Each UseLnspect your sander. Check for:* alignment of moving parts,o binding ol moving parts,o broken or damaged parts,oloose spindle washer an

When Sanderis RunningBefo[e starting your :work,watch the sander while it runs.If it:imakes;: an! dnfamiiiar: noise o:r vibrates excessively,: stop i

Motor Specifications and Electrical Requirements ...General Electrical ConnectionsDANGER: To avoid electrocution:1. Use only identical repl

Motor Specifications and E/ectrical Requirements (continued)Motor Safety Protecti onIMPORTANT: Tb avoidmotor damage; this motor shouldbe_blown' O

Unpacking and Checking1, Remove tooi from carton by liftingunit,2. Place the tool on a secure, stationary work surface andtook the tool over carefully

CAUTION: To avoid injury from tool movement,supporting surface where spindle sander ismounted should be examined carefully aftermounting to insure no

Clamping Spindle Sander To WorkbenchAn alternative method of mounting is to fasten the spindlesander to a mounting board. The board should be suffi-ci