Craftsman 113.201892 Spécifications télécharger pdf (Page 3)

e. Neverconnectthe workcableorclamptoany

objectbutthework pieceormetalworktable_

Connectingto otherobjectssuchasbuilding

ground can cause stray currentsto flow,

resultingin overheatingor fire.

4. PREVENTATIVE MAINTENANCE

'a. Never apply power to the welder with any part

of the "cabinet" removed. Position on-off

switch in "off" position and disconnect welder

from the power supply before doing

maintenance work inside the machine.

Removal of the welder cabinet should be done

only by a qualified service technician.

b. Before connecting the welder power cord to

the receptacle, check the following:

1. Inspect the power cord and welding cables

for cuts or burns and make sure blades and

ground pin on the plug are straighL

2. Inspect "ON-OFF" switch Iever for cracks or

broken parts.

3. inspect electrode holder jaw insulators for

cracks or broken parts.

c. Never weld anything on or to the welder

cabinet, as a burn through may cause

transformer failu re.

d. If any part of your welder is malfunctioning or

has been damaged or broken, such as switch,

cables, helmet, electrode holder, cease

operation immediately and disconnect welder

from the power source and turn switch "OFF"

until the particular part is properly repaired or

replaced.

5. ADDITIONAL SAFETY INFORMATION

a. For additional safety information, purchase

copies of "Practice for Occupational and

Educational Eye and Face Protection" (ANS!

Z87.I), "Safety in Welding and Cutting" (ANSI

Z49_!);_and "Fire Prevention in Use of Cutting

and Welding Processes" (ANSI/NFPA No.

51B) from the American National Standards

Institute, t430 Broadway, New York, New

York, 10018. Purchase copies of "OSHA Safety

and Health Standard" 29 CFR 1910 from the

U.S. Government Printing Office, Washington,

D.C. 20402.

SPECmFgCATIONS

INPUT

Volts AC ................................. 230

Hertz (Cycles) ............................. 60

Rated Input Amps .......................... 50

Delay Action Type Circuit Breaker or Fuse 50Amp

Short Circuit Amps ........................ 67

Power Cord Length ........................ 6'

OUTPUT

AC Low Range Amps .................. 35-140

AC High Range Amps .................. 50-230

DC Range Amps ....................... 30-140

Arc Voltage ................................ 25

AC Open Circuit Volts (max) ............... 74

DC Open Circuit Volts (max) ............... 80

Kilo-Volt-Amps ............................ t2

Kilo-Watts ................................ 7.2

Power Factor % ............................ 60

Duty Cycle % .......................... 20-100

GENERAL

E_ectrode Capacity .................. 1/!6_3/16

Low Hydrogen ....................... !/!6-1/8

Stainless Steel ....................... 1/!6-1/8

Aluminum ........................... 3/32-1/8

Electrode Cable Length .................... 8'

Work Cable Length ........................ 8'

Dimensions ...................... t5 x 12 x 2t

READ AND OBSERVE THE INSTRUCTIONS

APPEARING ON THE WARNING INFORMA-

TION FOUND ON THE CABINET,

ELECTRODE HOLDER AND ON THE INSIDE

OF THE WELDING HELMET,

I ..,_ WARNING E_ECTR,CSHOCKCANBEfATAl'BEfOREI

TURNING WELDER ON. CHECK THE ELEC]ROOE HOLDER TO

BE SURE I'HA_ THERE ARE NO PROTRUDING ,SCREW H_:ADS

ANO THAT ALL INSULATION IS SiECURE

CAUTIg_

U_ 0rdy for!a_ a_d eye p_D_e_b0n

a,_ams_ _dun0u_ _y_ _0m ar_ we_d-

h1_erp!ale Impac_ _e_stantey_ p_9-

tect_o_!hll_ p_a_ ba_k-up p!atR o_

Separate _a!e_y _p_la_es_ should

Impact Tes_sIant plple$ _ t_0T u_'_-

br_akPbi_ P_'t$_0 rsc_'alchedpla_e_

_-r_lechon-- ;_pface_mme_a_I¥

_s_ect _ouen_v and _mmed_a_e_v

LENS @ "_

SHADEN0

MADE f# _TALY

WARNING! ARC WELDING CAN BE iNJURIOUS TO OPERATOI_ AND PERSONS

IN THE WORK AREA _ CONSULT OWNERS MANUAL BEFORE OPERATING

To get the most from your welder we suggest you read the manual carefully --

even if you're an accomplished welder, and keep it available to serve as a

handy reference, or in the event that repair parts would be required.

FULL ONE YEAR WARRANTY ON CRAFTSMAN ELECTRIC WELDER

If this Craftsman Electric Welder fails to perform properly, due to a delecI in material or workmanship, within one year

from the date of purchase, Sears will repair it free o{ charge. this warranly applies only while this product is in use in the

United States

WARRANTY SERVICE IS AVAILABLE BY SIMPLY RE[URNING THE WELDER TO THE NEAREST SEARS STORE OR

SERVICE CENTER THROUGHOUT THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS. ROEBUCK AND CO,. Dept. 698/731A. Sears Tower. IL 60684

1 2 3 4 5 6 7 8 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Craftsman 113.201892 Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Système de soudage Craftsman 113.201892