f Save This Manual "_For Future Reference___JRSowner'smanualMODEL NO.113.23460010" COMPOUNDMITER SAWSerialNumberModel and serial number
Step Two--Checking and Aligning Blade with TurnTable Slot1. The blade should look like it's parallel to the sidesof the turn table slot. The blad
Step Four--Pivot AdjustmentsNOTE: These adjustments were made at the factoryand normally do not require readjustment.1. The miter saw should rise comp
Fence PositionsThe miter saw has two fence positions, The front fenceposition is used for workpieces up to standard 2 x 4 forcut off and bevel operati
NOTE: Pay attention to pieces removed, noting theirposition and direction they face (see illustration) Wipethe blade collars clean of any sawdust befo
If the saw is to be used in a portable application, mountthe saw to a 34" piece of plywood. The mounting boardcan then be clamped down to prevent
o o o o14" .,,!Attach mounting board to holes indicatedFRONTSIDECATALOG NO. 9-22244 LEG SEToo"J ._,._orn O15
BEFORE USING THE MITER SAW:WARNING: To avoid mistakes that could causeserious permanent injury, do not plug the mitersaw n until the following steps a
Dress for safety.Any power miter saw can throw foreign objects into theeyes. This can cause permanent eye damage. Wearsafety goggles (not glasses) tha
Never confine the piece being cut off. Never hold it,clamp it, touch it, or use length stops against it whilethe blade is spinning. It must be free to
MiterCutWhena mitercut is required,movethe sawto thedesiredangle.Donotstandinfrontofthesawtable.MovewiththehandtetothemiterangletomakethecutNOTE:Remem
FULL ONE YEAR WARRANTY ON CRAFTSMAN MITER SAWIf within one year from the date of purchase, this Craftsman Miter Saw fails due to a defect inmaterial o
Compound CutWhen a compound cut is required, select the correctbevel and miter position. Move with the handle to themiter angle to make the cut if the
Workpiece SupportLong pieces need extra supports• The supports shouldbe placed along the workpiece so the workpiece doesnot sag and your hand holding
Filler Blocks for Cutting Crown MoldingsThe majority of crown moldings have contact surfacesof 52: and 38 to the rear surface of the molding. Whenjoin
maintenance and lubricationMaintenanceAlways unplug the power cord before any maintenancecheck on this saw.DANGER: Never put lubricants on the blade w
TROUBLE SHOOTING GUIDE - MOTORPROBLEM1Brake does not stopblade within2-3 seconds.Motor does not start.Brush sparking whenswitch released.PROBABLE CAUS
BRUSHWHITEBLACKIIIITRIGGERSWITCHSHORT BLUELONGBRAKEBRUSHCIRCUIT DIAGRAMNOTES25
PARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.23460012o._ 19 ---,-_ _23 "''_\\26
repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.234600Always order by Part Number--Not by Key NumberFIGURE 1KeyNo.234567
repa=r par-t PARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.2346001423 222 1.-_+-- \+1816153482 °10 _12Always order by Part Number
repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.234600141113121 29 16 J-f 4111098Always order by Part Number--Not by Key
CHECK DAMAGED PARTS. Check for:• Alignment of moving parts,• Damaged electric cords.• Binding of moving parts,• Broken parts,• Stable mounting,• Funct
repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.2346001615/"131821/2O19 1121/71133O
repair partsPARTS LIST FOR CRAFTSMAN 10" COMPOUND MITER SAWMODEL NO. 113.234600Always order by Part Number--Not by Key NumberFIGURE 4. Blade &
CARBIDE TIPPED BLADESSAFETY INSTRUCTIONS & WARNINGSOSHA required industrial users to inspect tool prior to mountingfor cracks, chipped or bent tee
ff _AIRSowner'smanualSERVICEMODEL NO.113.23460010" COMPOUNDMITER SAWHOW TO ORDERREPAIRPARTS10-1NCH COMPOUNDMITER SAWNow that you have purch
• Roll long sleeves above the elbow.• Noise levels vary widely. To avoid possible hearingdamage, wear ear plugs or muffs when using mitersaw for hours
glossary of terms for woodworkingArborThe shaft on which a cutting tool =s mountedBevel CutAn angle cuthng operation made through the face ofthe work
MOTOR SAFETY PROTECTIONCAUTION: To avoid motor damage, this motorlshould be blown out or vacuumed frequently to Jkeep sawdust from interfering with no
UNPACKING AND PREASSEMBLYWARNING: To avoid injury from unexpected start-ing or electrical shock, do not plug the power cordinto a source of power duri
knowing your miter saw1. Warning label2 Handle Latch--The miter saw can be locked in thelowered position for compact storage3. Fence Lock Handles--The
assembly and alignmentASSEMBLY AND ALIGNMENTHANDLELATCHAssembling the Lower Blade GuardNOTE: For compact shipment the lower blade guardhas been partia
Commentaires sur ces manuels