Owner's Manual12 in. COMPOUND MITER SAWDouble InsulatedModel No.315.212120Save this manual for future reference.A CAUTION: Read and follow
FEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 3.Before attempting to use your saw, familiarize yourself with all operating features and safety requir
FEMURESCARRYING HANDLESee Figure 4.For convenience when carrying or tiwisporting your miter saw from one place to aitother, a carrying h
FEATURESPOSITIVE STOPS ON MITER TABLEPositive stops have been provided at 0“, 15“, 22-1^, 31.62“, and 45“ on both ttie left and right side of the mite
ADJUSTMENTSA WARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts to your saw before connecti
ADJUSTMENTSLOWER BLADE GUARDARROWFUT(S) ON SPINDLEINNER BLADE WASHER WITH DOUBLE'ly FLATSBLADE BOLTOUTER BLADE WASHER WITH DOUBLE "O'FL
ADJUSTMENTSNote: Many of the illustrations in this manual show only portions of your compourKi miter saw. This is intentional so that we can clearly s
ADJUSTMENTSUsing a 6 mm hex key, kx>sen the socket head screws securing the fence. See Figure 16. Adjust the fence ieft or right untii №e framing s
ADJUSTMENTSThe edge of the square and the saw blade should be parallel as shown in figure 17.If the front or back edge of №e saw blade angles away fro
ADJUSTMENTSFENCEMITERTABLE BLADEVIEW OF BLADE NOT SQUARE WITH MITER TABLE, ADJUSTMENTS ARE REQUIRED Rg. 23Using a 10 mm wrench or adjustable wrench, l
ADJUSTMENTS Lower the blade into the zero clearance throat plate of the miter table. Check blade clearance and maximum cutting distance (distance fr
TABLE OF CONTENTSTable of Contents...
OPERATIONFig. 26Place the workpiece flat on the miter table with one edge securely against the fence. If the board is waiped, place the convex side ag
OPERATIONBEVEL CVrrFig. 28Loosen the bevel lock knob and move the saw atm to the left to the desired bevel angle.Bevel angles can be set from 0” to 45
OPERATIONTO MAKE A COMPOUND CUT WITH YOUR MITER SAW; Pull out the lock pin and lift saw arm to its fuli height. Loosen the miter lock handle. Rota
OPERATION Before turning on the saw, perform a dry run of the cutting (^ration just to make sure that no problems will occur when
OPERATIONCUTTING COMPOUND MITERSTo aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts
OPERATIONCUTTING CROWN MOLDINGYour compound miter saw does an excellent job of cutting crown molding. In gerreral, compound miter saws do a better job
OPERATIONWhen cutting crown molding by this method the bevel angle should be set at 33.85°. The miter angle should be set at 31.62° either right or le
MAINTENANCEWARNING: When servicing, use only identicat Craftsman replacement parts. Use of any other part may create a hazard or cause product damage.
MAINTENANCEiW WARNING; To ensure safety and reliability, all repairs — with the exception of the externally accessible brushes — should be performed b
29
RULES FOR SAFE OPERATIONThe purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120Figure A30
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120The model number will be found on a plate attached to the motor housing. Always m
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120roFigure B
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120The model number will be found on a plate attached to the motor housing. Always mention the mode
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212120SEE NOTE “A”21 20Figure C
CRAFTSMAN COMPOUND MiTER SAW - MODEL NUMBER 315.212120The model number will be found on a plate attached to the motor housing. Always m
For in-home major brand repair service:Call 24 hours a day, 7 days a week 1-800-4-MY-Home®« (1-800-469-4663)Para pedir servicio de reparación a domici
RULES FOR SAFE OPERATION (Continued)USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, b
RULES FOR SAFE OPERATION (ContinuecQALWAYS SUPPORT LONG WORKPIECES tominimize risk of blade pinching and kickback.Saw may siip, waik, or siide whiie c
ALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your saw) to cause a careless mistake. ALWAYS REMEMBER that a careless fra
PRODUCT SPECIFICATIONSBlade Diameter12 in.Cutting Capacity with Miter at O^/Bevel 0°:Blade Arbor5/8 in.max width x resulting height 7-7/8 in. x 2-1/2
The following labels are on the miter saw with loca tions indicated.Restore lower blade guard and securely tighten screw before useDANGER: DO
LOOSE PARTS LISTThe following items are included with your Compound Miter Saw:Saw Blade -12 in. Miter Lock Handle Dust Guide Blade Wrench5 mm Hex Key
Commentaires sur ces manuels