Craftsman 247.298780 Manuel du propriétaire télécharger pdf (Page 13)

,'y :

FIGURE 29. ':'

TILL!NrG

1., Adj_is.{the depth stat<e bY pullJ.ng: the depth

stake atJjiJstment pin, Release the depth

30.

2, Lower the depth stake for transpdrtlng the

tiller,

3. Engage wheel engagement lever, select gear

on handle panel and ti!let will propel itself:

A, For tilling !n sod, raise the depth stalke so

the depth bar is one to two inches above

tt_e ti:nes.

Ti_is sett!ng {s _ised for breaking up the

sod .and shallow Cultivation. For further

depth ra}se theedepth stake and -make one

or two more passes over the area,

B_ For fitting loose and sandy soil, further

depth tn tilling can be achieved by raising

the depth stake to its higllest setting.

When tilling, if a hard spot or rock is

encountered, the tines may lift the

back Of the tiller out Of the ground

and start to walk across tlle ground,

To correct this problem raise up on

the handles,

TiLL:iNG:Hg NTS

Soil conditions a_e imp.ortaht for proper tilling.

The t!nes will not. readily penetrate dry, hard s0tl,

This may con.tribute to ex6essive bounce and

dill!out| handling of.the tiflei. Hard'soii should be

moistened prior to tilling,

ExtremelY Wet soi! wilt cause .soil 1o ball up or

clump,

When tilllhg in the Fall, all vines and long gt_ass

should be removedo This will preveht vibes from

wrapl_:lng around _he fine s h_ft Whlcl_ slows ttl!ing

operation,

The best method will be determined by the soil

condition, In some soils, the desired depth "is

obtained the first time over the garden, tn other

so.ils, the desired depth Is obtained by going over

the garclen two or three times_ In the latter' t_ase,

the depth stake should be raised (raising the

depth stake increases diggliqg depth) before each

suc.oeeding pass over the garden, and passes

st'io!jtd be made across the ierigth and width of the

garden alternately,. Rocks' which Are turned up

should be removed from thega¢dei_ area.

Handle Pressure: Eurther O0nt#ol of ttll!ng depth

and,t_:avet speed can be ol_tained by variation of

p_es_.ure on t_he handles.

When .using the depth stake e(downward pressure

onthe, handles Will increase the working depth

ahd 're.duce the' f0cwai'd_ speed. An upward

ptes.sti.r.e o,n tlie handleswill reduce the working

deistic:and tncrease the fo_ard speed, The type of

sotl arid wi_kt_qg conditioris Wilt determine the

actual se.t.t;!ng Ofthe;.deptl_ _J!ake,

tVlAINTENANCE

BELT RE,PLACEMENT:

_o not use a'n off:the-shelf belt.

If belt replacemer_t is required, ordei" belt or belts

by part number from your nearest Sears Service

Center.

Part No. 754-0220 Part No. 754-022t

5/8" x 27" Short Belt 5/8" x 52" Long Beh

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Craftsman 247.298780 Manuel du propriétaire Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses Craftsman 247.298780