Craftsman 247.88110 Manuel d'utilisateur

ownersmanualMODEL NO. 247.88110CAUTION:Read SAFETY RULES and INSTRUCTIONS carefullyCRAFTSMAN HI WHEEL SELF PROPELLED ROTARY MOWER• Assembly• Operatin

Step 7. Assemble the other control rod and lockout lever to the pivot lever on the lower Left Hand side of the mower with ferrul

Lockout Lever Engaged PositionFIGURE 23. DRIVE MECHANISM ENGAGEDFIGURE 24 BLADE ENGAGED4. Figures 23 and 24 show lockout levers engaged and locked ove

2. Service engine with clean fresh regular gasoline.3. Service engine with SAE 30 weight motor oil. Fill oil fill opening to overflow. See f

2. The deck may be cleaned by tilting the mower backward or on its side and scraping clean with a suitable tool or by washing w

2. Remove the hex lock nut holding the lockout lever in position.3. Turn the lockout rod and lever in or out of the ferrule unt

1. Throttle Control—If throttle adjustment becomes necessary, the throttle control wire may be reset as follows:a. Loosen, but do not

5. Blade Spindle AssemblyThe blade spindle assembly, located on the underside of the mowing deck, is equipped with a grease fitting Use grass dischar

7. Tip mower on its right hand side and remove the oil drain plug.FIGURE 39. OIL DRAIN LOCATIONENGINE MAINTENANCECAUTIONStop the engine and disco

CARBURETOR ADJUSTMENTS STORAGE INSTRUaiONSDo not make unnecessary adjustments. Factory settings are correct for most applications. If ad

TROUBLE SHOOTING CHARTCAUTION: ALWAYS DISCONNECT SPARK PLUG BEFORE ATTEMPTING ANY REMEDY.TROUBLELOOK FORREMEDYBlocked fuel line or empty gas tank.C

IMPORTANTSAFE OPERATION PRACTICES FOR WALK-BEHIND MOWERSTRAINING1. Read the Operating and Service Instruction Manual carefully. Be thoroughly f

CRAFTSMAN HI WHEEL SELF-PROPELLED ROTARY MOWER MODEL 247.88110K>o(DTJQ oQ</)

CRAFTSMAN HI WHEEL SELF-PROPELLED ROTARY MOWER MODEL 247.88110MREF.NO.PARTNO.DESCRIPTIONREF.NO.PARTNO.DESCRIPTION1 712-107Hex Center Locknut 14-20 Thd

CRAFTSMAN HI WHEEL SELF-PROPELLED ROTARY MOWER MODEL 247.88110(DTDQT3Q</)

CRAFTSMAN HI WHEEL SELF-PROPELLED ROTARY MOWER MODEL 247.88110MuREF.NO.PARTNO.DESCRIPTIONREF.NO.PARTNO. DESCRIPTION1 710-121Hex Scr. ’/2-20 X .75"

'//

CRAFTSMAN HI WHEEL SELF-PROPELLED ROTARY MOWER MODEL 247.88110M(IIREF.NO.PARTNO.DESCRIPTIONREF.NO.PARTNO. DESCRIPTION1710-117Hex Scr. 5/16-24 x 1.00&q

BLADE SPINDLE ASSEMBLY 901-78052. Zerk Fitting should face Discharge Chute of Deck.3. Lubricate every 8 to 10 hours with Shell General Purpose Greas

p Must Not Toiiti]^ Where Blade Is27

NOTES:28

NOTES29

iMHWMMW iiwwmwmtCRAFTSMAN 1-YEAR GUARANTEEIf during the first year this Craftsman product fails to give proper performance due to defects in material

TECUMSEH 4-aCLE ENGINEMODEL NUMBER: V60-70259Hf------13730

TECUMSEH 4-CYCLE ENGINEMODEL NUMBER: V60-70259HRef.No.PartNo. Part NameRef.No.PartNo.Part Name133361Cylinder Assy. (Incl. Nos. 2 &51 650697Screw,

TECUMSEH 4-CYCLE ENGINEMODEL NUMBER: V60-70259HRef.No.PartNo. Part NameRef.No.PartNo.Part Name113114115117118 119121122123124 126127128 129 13130588A2

MAGNETO NO. 610689ARef.No.PartNo.Part NameRef.No.PartNo.Part Name610689A Magneto10610593Screw, Condenser fastening1 30555Flywheel1130843Tab, Ground te

Ref.No.PartNo.Part NameRef.No.PartNo.Part Name631444 Carbxiretor 16631025Bowl & Drain Assy., Float1 31834 Shaft & Lever Assy., Throttle (Inch

REWIND STARTER NO. 590420Ref.No.PartNo.Part NameRef.No.PartNo.Part Name590420Starter, Rewind7590414 Spring & Keeper Assy.1 590409Screw, Retainer85

ownersmanualMODEL NO. 247.88110SearsSERVICE is at Yoar SERVICE wherever Yea live or move in the U.S.A.How to ORDER Repair PartsThe Model Number wil

REFERENCE PHOTO FOR ASSEMBLY AND INSTRUCTIONSUpper Handle (2) Throttle ControlLK;-/Blade EngagingLever (Under Handle ', Panel)Throttle Control Ca

INDEXSafe Operation Practices___________________________2GuaranteeMaintenance Agreement Customer's ResponsibilitiesSet-Up Instructions-----------

Step 2.Lower Handle(2) Flatwashers %" I.D. X 1 'A" O.D.Hex Hd. Bolt— --16x 1'FIGURE 5 LOWER HANDLE ASSEMBLYStep 1.a. Place the lo

d. Secure the two (2) upper handles together with one (1) Hex Hd. Bolt %-20xl%" and one (1) Hex Center Lock Nut '/4-20 Thd.N

FIGURE 12. LOCKOUT BRACKET ASSEMBLYd. Place the lockout bracket assembly under the "T" portion of the upper handle with the b

b. Secure bottom of handle panel to handle assembly with two (2) Hex Hd. Bolts Va-2Q x 1 '/2" and two (2) Hex Center