Craftsman 247.298760 Manuel d'utilisateur

ownersmanualMODEL NO.247.298760CAUTION:Read SAFETY RULES and INSTRUCTIONS carefullyCRAFTSMAN.8H.P. FOUR SPEED CHAIN DRIVE TILLER• Assembly• Operating•

OIL AND FUEL RECOMMENDATIONSA^CAUTIONOil must be added before starting.To start and operate your Tecumseh engine, you wiil need the foliowing:1. Fili

3. Choke Engine. Push choke lever to choke engine. See figures 22 and 23. Once the engine starts, puil back on choke iever.FIGURE 23.4.

2. Throttle Control: The throttle control lever is located on the right hand side of handle panel.A. Stop—Pull lever back (upward) to stop th

Tilling width can be increased from 26 inches to 28 inches by removing the clevis pin and hair pin cotter and sliding the outer tines out one (1

2. Push forward on the idler and lift belt off of chain case pulley, idler pulley and variable speed pulley. See figure 32.FIGURE 32.Re

and detergent solution and flush from inside until water is clear. Be sure filter is completely dry before reassembling to engine. DO NOT

///^Control Bracket/ muSTORAGEFIGURE 37.3. NEVER TAMPER WITH ENGINE GOVERNOR WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING ENGIN

NOTES17

Repair Parts 8-H.P. Tiller Model 247.29876029 2718

Repair Parts 8-H.P. Tiller Model 247.298760REF.NO.PARTNO.DESCRIPTIONREF.NO.PARTNO.DESCRIPTION1710-0160Hex Wash. Hd. AB-Tapp Scr.28736-0119L-Wash. 5/16

annrrrrrryriTrTrrrrrnnr » Clll IrrnrrrrTBT-BTTTrrrrrrrrrrrnnnnrgTTTrrrrrm^TTVTvmFULL ONE YEAR WARRANTYFor one year from the date of purchase, Sears w

Repair Parts 8-H.P. Tiller Model 247.298760-----29—30 3120

Repair Parts 8-H.P. Tiller Model 247.298760REF.NO.PART 1 NO.DESCRIPTIONREF.NO.PARTNO.DESCRIPTION1 .^52-0663 Engine Tecumseh Model2804898Belt Guard Su

Repair Parts 8-H.P. Tiller Model 247.29876028fO|' f 29 30 3) 1NOTE: Use 14 ounces ofPlastilube #1Order Part No. 737-0133Repair Parts Transmissio

TECUMSEH 4-aCLE ENGINE MODEL NUMBER: HM80-155162E12612492-^\76'^-d^82 83 >97- 77 161/ti -7128 14923

TECUMSEH 4-acU ENGINE MODEL NUMBER: HM80-155162ERef.Part Ref.PartNo.No.Part NameNo.No.Part Name134348Cylinder Assy, (Incl. Nos. 2,3&4)57*34031Gask

TKUMSEH 4-aOE ENGINE MODEL NUMBER: HM80-155162ERef.No,PartNo,Part NameRef.No.PartNo.Part Name148149 161 16233267650513631979610842Bracket, Air cleaner

MAGNETO NO. 610842The complete magneto is not available as an assembly. The .magneto number is shown for reference purposes only. Order component part

ownersmanualMODEL NO. 247.298760SearsSERVICE is atYoarSERVICEHOW TO ORDER REPAIR PARTSThe Model Number will be found stamped on a plate att

IMPORTANTIt is suggested that this manual be read in its entirety before attempting to assemble or operate. Keep this manual in a safe place for futur

INDEXWarranty...2Rules for Safe Operation...3In

ISFIGURE 3. (SHOWN IN FULL SCALE)The letters listed below will be referred to throughout the following text for easier hardware identific

TILLERIDENTIFICATIONHandle BarSpark Plug Oil Dipstick Fuel Tank CapTineShieldTine AssembliesDepth StakeBelt CoverWheel Yoke AssemblyFIGURE 4.

ASSEMBLYINSTRUCTIONS1. Handle Panel Attachment.For shipping purposes, the handle mounting brackets are pivoted down. With a 9/16” wrench

C. Secure with hex center locknut (G). See figure 9.Pivot Arm Assemblyt"/FIGURE 11.FIGURE 9.H^^NOTETighten hex locknut just to the point the rub

NOTEShift lever and control rod must be readjusted whenever you change the handle height.5. Tine Attachmenta. The outer tines have been reversed on t